Product Description
A Designer Series premium quality, high hide
primer. A coating for use on new interior drywall,
plaster, concrete, brick and acoustical tile. May be
used as prime coat both before and after texturing.
It is designed to provide a uniform base suitable for
any type of finish coat, and has excellent enamel
holdout and excellent Anti-Mold™ and Anti-Fungus™
properties to protect the paint film only*, when used
under enamel finish coats.

Performance Characteristics
o Contains Mildewcide to protects the paint film
o Do not contain Polybrominated Diphenyl Ethers
o Seals drywall and plaster
o Formulated for extra hide
o Easy to apply
o Quick drying
o Easy clean-up with soap and water

Surface Preparation
Previously Painted Surfaces
All surfaces must be clean, dry and free from dirt,
wax, grease, oil, chalk, mildew and loose or peeling
paint. For best adhesion, glossy surfaces should be
lightly sanded. Nail holes, cracks or other surface
imperfections should be properly filled, sanded
smooth and dusted clean. Glossy surfaces must be
sanded or deglossed and wiped clean. All bare
areas must be primed. All mold, mildew, and fungi
must be completely and thoroughly removed and
cleaned by using Betanix® 100.1 before painting. Always wear a dust mask when sanding.

Wallboard and Plaster
When applying to new concrete, plaster or texture-
coated surfaces, allow the surface to cure properly.
All new drywall and plaster must be sealed with Primer
BX1000 Interior Wall Primer - Sealer before finish coat.

Application Suggestions
IMPORTANT! READ BEFORE APPLICATION:
If more than one package of the same color is to be
used, mix together before applying to ensure uniform
color and finish. Apply paint to a small test area on
surface for color approval before painting entire
surface.

STIR WELL BEFORE USING. May be applied by
brush, roller or spray. When spraying, follow spray
equipment manufacturer's recommendations
carefully. Apply only when the temperature of the
surface, material and air is above 50°F.

DO NOT ALLOW THIS PAINT TO FREEZE.
FREEZING MAY REDUCE THE QUALITY AND THE
PERFORMANCE OF THE PAINT.

System Suggestion
For maximum performance and better results follow
this suggested recommendation.

Two coats Primer - Sealer at 1.5 mils
DFT each coat and two coats Finish top
coat at 1.5 mils DFT each coat.

CAUTION!
Do not take internally. Use only with adequate
ventilation. Avoid breathing vapor, spray mist or
sanding dust. Sanding dust may cause eye and
skin irritation. Avoid contact with eyes. Avoid
prolonged or repeated contact with skin. Avoid
contact with eyes. Avoid prolonged or repeated
contact with skin. Close container between uses.

KEEP OUT OF REACH OF CHILDREN!
This product contains chemical(s) known to the
State of California to cause cancer and birth defects
or other reproductive harm (Prop. 65).

Environmental Considerations
Formulated without lead, mercury or chromium.

Disposal Information
Dispose in accordance with all Federal, State and
local regulations. Please use all of the paint before
disposing of the container. If no paint can be poured
or drained from the container, dispose of the dry,
empty container as you would normal household
waste. Store any excess product in a tightly sealed
container away from heat or flames. To dispose of a
full or partially full container of paint, contact your
city or county government for hazardous materials
collection locations and operating hours. Do not
dispose of excess paint in any sanitary or storm
water sewer system.

APPLICATION EQUIPMENT

WEIGHT PER GALLON:

THINNING: Apply at package consistency. DO NOT
THIN. DO NOT USE PAINT THINNER.

EQUIVALENT FEDERAL SPECIFICATIONS:
Meets the performance requirements of Federal
Specification: TT-P-19D, TT-P-96 (not necessarily
composition)

DESIRED FILM THICKNESS:
Wet - 5.0 mils
Dry - 1.5 mils

COVERAGE: Approximately 300-350 square feet
per gallon depending on surface texture and
porosity.

CLEAN UP: Clean brushes, rollers and equipment
with soap and water. Clean spills and spatter
immediately.

INGREDIENTS

Note: To the best or our knowledge, the information contained herein is accurate. However, Betanix® assumes no liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of the suitability of any information or material for the use contemplated, the manner of use and whether there is any infringement of patents is the sole responsibility of the user. Additional information may be obtained thorough your local sales representative or the Betanix Sales Office.

(back)